Window motor repair cost

Window Regulator Motor Replacement Cost – RepairPal Estimate. The average cost for window regulator motor replacement is between $279 and $378. Labor costs are estimated between $94 and $118 while parts are priced between $185 and $260.
Click to see full answer

How do you know if its the window regulator or the motor?Power window goes down, but not up, the motor is not running when the switch is in "UP" position. Window motor runs but the window jams or doesn't move: In this case, we know that the window switch, the wiring and the window motor work. That means the problem is with the window regulator.

How do you fix an electric window that wont go up?

Here are some basic troubleshooting tips to try when your electric windows won't roll up or down:

  1. Check the window safety lock-out switch.
  2. Check the fuses.
  3. Push the window switch up and down and listen.
  4. Push the window switch and watch the dash gauges.
  5. Try the other switches.
  6. Swap switches if possible.

More items•

What causes the power window to stop working?

One of the most common reason power windows can malfunction is because the window regulator and cable come apart from one another – the cable can break or come off the pulley. The power window system may sound like its working but if the cable is not winding up correctly, you window will be stuck.

How much does it cost to replace a power window motor?

Average Cost for Full Replacement of Power Window Motor
The cost of a motor varies depending upon the type of car, but it usually runs in the area of $150 to $300 dollars.

Related Questions

How do I know if my power window motor is bad?

Symptoms of a Bad or Failing Window Motor / Regulator Assembly

  1. It takes multiple presses to roll the window up or down.
  2. Window speed is slower or faster than usual.
  3. Clicking from the door when the window rolls up or down.
  4. Power window won't stay up or is crooked.

How do I know if my window motor or switch is bad?

Symptoms of a Bad or Failing Power Window Switch

  1. All the windows quit working.
  2. Only one window stops working.
  3. Window works from master switch only.
  4. Windows work sometimes.

How do I manually raise a power window?

How to Pull Up Power Window Manually

  1. Step 1: Take Out the Door Panel.
  2. Step 2: Detach the Window from Motor.
  3. Step 3: Find and Disconnect the Motor.
  4. Step 4: Attach the Window to the Motor and Raise It.
  5. Step 5: Put Back the Door Panel.

Why would only one power window not work?

If only one window stops working, the problem could be a bad relay, fuse issue, bad motor, or the power window switch has failed. The most common reason for one window to stop working is the switch, so this should be looked at by a professional mechanic to have your power window switch replaced.

How do you test a power window switch?

To test the window switch you will need to use a voltmeter and ohmmeter.

  1. Remove the faulty window switch from the door.
  2. Turn the switch to the "open" position.
  3. Attach the voltmeter to the switch plug and test to see if there are 12 volts coming from terminal 4 to the ground and from terminal 5 to the ground.

More items

Can you manually roll up a power window?

Hold the window shutter from the top and bottom and then take out the props supporting them. Tighten back the nuts that hold the window back to the regulator ledge. Ensure that you fasten the screws well. Then, place your hands beneath and above the window and pull it up as high as you can.

How do I reset power windows after replacing battery?

Hold the key for 2-5 seconds after the window closes.
Once the window is all the way up, hold the button in the up position for 2-5 seconds. Once you've done this, release your finger. The automatic power settings for that window should be reset.

What do you do when your electric window wont go up?

Door Slam Method

  1. Turn your car on.
  2. Push and hold your window switch down in the desired direction (up or down) as you complete the following step.
  3. While continuing to hold the button down, sit inside your vehicle and slam the car door. Repeat this step a few times and see if the window begins to roll up or down.

How much does it cost to fix a window that wont roll up?

Repair costs to fix a window that won't go up can be $20 or less if you're only dealing with a new fuse that you replace yourself. More complex repairs that involve dismantling the door to access the window motor can run $250 to $400 or more.

Does each car window have its own fuse?

Other cars have individual fuses for each window motor so failure will only affect the one window. In some cars the fuse is in the main fusebox but many makers use in-line fuses so check with your manual to find where the fuse is and replace it if blown.

Why is driver side window not working?

If the fuse is blown, pushing a window button will do nothing at all: The motor won't groan and the glass won't quiver. If the fuse is good and you can hear the motor, or the glass acts like it wants to move, then you've got some sort of mechanical problem. If not, check the fuse.

How do I know if my power window switch is bad?

If you suspect your power window switch is going bad or failing, watch for the following symptoms:

  1. All the windows quit working.
  2. Only one window stops working.
  3. Window works from master switch only.
  4. Windows work sometimes.

How do you roll up a broken power window?

Two Ways to Roll up a Power Window That Stopped Working

  1. Turn the ignition key to the on or accessory position.
  2. Press and hold the window switch in the closed or up position.
  3. With the window button depressed, open and then slam the car door.

More items•

How do you pull up a stuck power window?

Troubleshooting a Stuck Electric Car Window
Press and hold the window switch in a closed position. Keep the button depressed and push the side that closes the window. Open and slam the car door while the window button is depressed. Try it a few times until the window opens.

How do you program a power window switch?

To program the window:

  1. Close all doors with the ignition in the ACC/ACCESSORY, ON/ RUN position, or when Retained Accessory Power (RAP) is.
  2. Press and continue to hold the window switch until the window.
  3. Pull up and hold the window switch to close the window.
  4. Repeat for each window that has the express-up feature.

Categories:

QA

Tags: